Orion-system VCC-X Controller Manuel d'utilisateur Page 48
- Page / 120
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PREHEAT-X CONTROLLER WIRING
VCC-X Controller Technical Guide
48
PREHEAT-X Controller Wiring
Figure 33: PREHEAT-X Controller to VCC-X Controller Wiring
M
ENTER
UP
DOWN
ALARM
MENU
ALARM CONTACT
HEAT 1
HEAT 2
HEAT 3
HEAT 4
HEAT 5
HEAT 6
RLY COMM
HEAT
OUTPUTS
ANALOG
OUTPUTS
0-10V MOD. SCR
GND
PWM +
PWM -
OE377-26-00061 PREHEAT-X AAON No.: V48510
WattMaster Label
#LB102XXX-A
Rev.: 1A
E-BUS
CONNECT
E-BUS
CONNECT
LAT1
0-10V RESET
LAT2
OAT
GND
GND
ANALOG INPUTS
BINARY INPUTS
RS-485 COMM
+24 VAC
GND
www.orioncontrols.com
www.aaon.com
ENABLE
T(-)
EMERG. SHUTDOWN
SHLD
FUTURE USE
R(+)
CONTACT RATING IS
1 AMP MAX
@ 24 VAC
AIN1
Entering Air Temperature
Sensor
Reset In 0-10 VDC
GND
+
-
Emergency
Shutdown
Line
GND
24VAC
40 VA
Transformer
Minimum
Heat 1 Relay
Heat 2 Relay
Heat 3 Relay
Heat 4 Relay
Heat 5 Relay
Heat 6 Relay
COM
Alarm
Note:
All Relay Outputs Are
Normally Open And Rated
For 24 VAC Power Only.
1 Amp Maximum Load.
Relay
Contact
–
PWM SSR
+
–
Modulating SCR
(0-10 VDC)
+
PREHEAT-X CONTROLLER
(OE377-26-00061)
AIN2
AIN3
RST
GND
GND
BIN1
BIN2
Leaving Air 2
Temperature Sensor
Leaving Air 1
Temperature Sensor
SAFETIES
(BY OTHERS)
N.C.
Heat Enable
Signal (24 VAC)
W1
NOTE: Reset In And Heat
Enable Inputs Are Used In
Stand-Alone Mode Only
Mount Inside PREHEAT-X
Box Wall
Make Splice
Connections
Inside Sensor
Enclosure
As Shown. Seal All
Conduit Fittings With
Silicone Sealant
Mount Sensor Outdoors
In Shaded Protected
Area & In Upright
Position As Shown
Mount Inside PREHEAT-X
Box Wall
M
ENTER
UP
DOWN
ALARM
MENU
ALARM CONTACT
HEAT 1
HEAT 2
HEAT 3
HEAT 4
HEAT 5
HEAT 6
RLY COMM
HEAT
OUTPUTS
ANALOG
OUTPUTS
0-10V MOD. SCR
GND
PWM +
PWM -
OE377-26-00061 PREHEAT-X AAON No.: V48510
WattMaster Label
Rev.: 1D
#S 000062W
E-BUS
CONNECT
E-BUS
CONNECT
LAT1
0-10V RESET
LAT2
EAT
GND
GND
ANALOG INPUTS
BINARY INPUTS
RS-485 COMM
+24 VAC
GND
www.aaon.com
ENABLE
T(-)
EMERG. SHUTDOWN
SHLD
FUTURE USE
R(+)
CONTACT RATING IS
1 AMP MAX
@ 24 VAC
www.orioncontrols.com
MSTP
BACnet
EBC E-BUS Cable
Connects To
VCC-X Controller’s
Expansion Port
PREHEAT-X Controller Wiring
The OE377-26-00061 PREHEAT-X Controller (AAON Part No.
V48510) is designed to control fi xed stages of Preheat and optional
modulating Preheat to maintain a desired Preheat Leaving Air
Temperature Setpoint. The PREHEAT-X Controller directly connects
to the VCC-X Controller or indirectly using an E-BUS Expansion
Board via an EBC E-BUS cable. See Figure 33 for wiring.
The following information will be passed between the PREHEAT-X
Controller and the VCC-X Controller:
Leaving Air Temperature Setpoint
Entering Air Temperature Setpoint
Preheat Enable Signal
Leaving Air Temperature Status
Entering Air Temperature Status
Alarm Status
If the communication is interrupted between the
PREHEAT-X Controller and the VCC-X Controller,
the PREHEAT-X controller will be disabled.
For more information, refer to the PREHEAT-X Controller Technical
Guide.
NOTE: If using multiple E-BUS Sensors or Modules, the
E-BUS Hub or Adapter Board may be required.
- VCC-X Controller 1
- Technical Guide 1
- TABLE OF CONTENTS 2
- System Features 5
- Applications 6
- Part Number Cross Reference 7
- VCC-X CONTROLLER 8
- Orion No.: OE338-26B-VCCX 8
- AAON No.: V42430 8
- OVERVIEW 10
- Parts and Descriptions 10
- VCC-X Controller Dimensions 14
- VCC-X CONTROLLER WIRING 15
- VCC-X EM1 Dimensions 16
- VCC-X Controller Input Wiring 20
- Wall-Mounted E-BUS CO 23
- Sensor Wiring 23
- Duct Mounted E-BUS CO 24
- Remote SAT Reset Wiring 29
- Supply Fan VFD Wiring 34
- Economizer Actuator Wiring 35
- Compressors Wiring 38
- Head Pressure Control 39
- Coil Temperature Sensors 39
- VCC-X EM1 40
- Expansion Module 40
- Return Air Bypass Wiring 43
- WARNING!! 44
- , GreenTrol 45
- , and Paragon Wiring 45
- MHGRV-X CONTROLLER WIRING 46
- MHGRV-X Controller Wiring 46
- MODGAS-X Controller Wiring 47
- PREHEAT-X CONTROLLER WIRING 48
- PREHEAT-X Controller Wiring 48
- START-UP & COMMISSIONING 49
- INPUTS & OUTPUTS 50
- RSMV Inputs & Outputs 53
- SEQUENCE OF OPERATIONS 55
- SEQUENCE OF OPERATIONS 56
- Cooling Mode 56
- Trend Logging 69
- VAV/Zone Controller Alarms 69
- TROUBLESHOOTING 71
- RSMV LED Diagnostics 73
- Diagnostic LEDs 73
- System Confi gurations 74
- Stand-Alone System Layout 75
- Modular System 76
- Manager SD 76
- Networked System Layout 77
- Temperature Sensor Testing 78
- OE275-01 Suction Pressure 80
- Transducer Testing for R410A 80
- Refrigerant 80
- Head Pressure Transducer 81
- Troubleshooting 81
- Navigation Keys 82
- Main Screens Map 83
- Settings Screens 83
- Settings Screens 84
- Status Screens 85
- Alarm Screens 86
- Output Override Screens 87
- APPENDIX C - RSMV LCD SCREENS 88
- System Status Screens 89
- Sensor Status Screens 90
- Diagnostic Screens 93
- VCC-X BACnet 96
- Connection To MS/TP Network 96
- VCC-X BACnet 97
- APPENDIX D - VCC-X BACnet 100
- VCC-X BACnet 101
- Parameters 101
Produits connexes et manuels pour Matériel Orion-system VCC-X Controller
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels