Orion-system VCC-X Controller Manuel d'utilisateur télécharger pdf (Page 25)

VCC-X Operator Interface SD

VCC-X CONFIGURATION

Conﬁ guration Screens

In order to correctly set up the VCC-X Controller, you must ﬁ rst

conﬁ gure several parameters in regard to the type of HVAC unit

and system you have installed. Most of these values and operat-

ing parameters are only set once at the initial system setup and are

never changed.

Modular Service Tool Instructions

No matter what screen or menu you’re in, press <CONFIGURA-

TION>. The Unit Selection Screen will appear, shown below, request-

ing that you enter the unit ID number.

VCC-X CONFIGURATION

RSM CONFIGURATION

Select & Press Enter

Enter the correct unit ID number of the VCC-X Controller you want

to conﬁ gure and then press

<ENTER>. Once communication is es-

tablished, the *00* message will go away. Then

press <>. Select

VCC-X Conﬁ guration and then press <ENTER>. Press <ENTER>

to save entered data and press <> to scroll through the screens.

NOTE: If the *00* remains, it indicates a communication

failure to the controller.

System Manager SD Instructions

From any Main screen, press <SETPOINTS>. The screen below

will appear because this option requires passcode clearance. Only a

Level 2 passcode can change setpoints.

THIS ACTION REQUIRES

PASSCODE CLEARANCE

Enter Passcode: XXXX

If the correct passcode was entered, the Unit Selection Screen will

be displayed.

Enter Unit Address

Then Press Enter

Selected Unit #_1

Press Down

Enter the correct unit ID number of the VCC-X Controller you

want to conﬁ gure and then press <ENTER>. Once communication

is established, the *00* message will go away. Then

press <>.

NOTE: If the *00* remains, it indicates a communication

failure to the controller.

The following screen will be displayed:

Change Setpoints

Configure Unit

Save/Copy/Restore

VCC-X CONFIGURATION

RSM CONFIGURATION

Select & Press Enter

On the ﬁ rst screen, scroll down to the ‘Conﬁ gure Unit’ option and

press <ENTER>. On the second screen, select VCC-X Conﬁ guration

and then press

<ENTER>. This will take you to the ﬁ rst Conﬁ gura-

tion Screen shown below.

Conﬁ guration Screen #1 - Sensor Scaling

VCC-X Cnfg ID #

Sensor Scaling

Fahrenheit

USE < or > TO CHANGE

Options are Fahrenheit or Celsius. If you make a change to this

screen, after you press <ENTER> to have the system accept the

change, you must return to the Unit Selection Screen to re-establish

communications with the Controller. Default is Fahrenheit.

Conﬁ guration Screen #2 - RSM #1 & #2

Module Installed

VCC-X Cnfg ID #

RSM#1 Installed: NO

RSM#2 Installed: NO

USE < or > TO CHANGE

If you have a one RSMV Module installed, the 1st conﬁ guration op-

tion should be conﬁ gured as YES. If you have a 2nd RSMV Module

installed, the 2nd conﬁ guration option should be conﬁ gured as YES.

Default is NO.

VCC-X Conﬁ guration Screens

Enter Unit Address

Then Press Enter

Selected Unit #_1

Press Down

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 95 96

Commentaires sur ces manuels

Pas de commentaire

Orion-system VCC-X Controller Manuel d'utilisateur Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Orion-system VCC-X Controller